Now you can replace your own high-frequency driver diaphragm!

Replacement Diaphragms for High Frequency Drivers Made Easy!

If you own a HF driver with a replaceable diaphragm assembly, you can fix it yourself quickly and easily! With just a few easy steps, and a replacement diaphragm available from LoudspeakersPlus.com, you can have your HF driver working again in a few minutes!

Just follow these easy-to-do Replacement Diaphragm instructions!
replacing a high frequency driver diaphragm 1.

Great care must be taken when replacing a diaphragm, so take your time and do it right!

Start by removing the scews that secure the diaphragm housing to the magnet. These are usually located on the front side of the magnet assembly.
replacing a high frequency driver diaphragm 2.

Carefully lift off the housing assembly. Clean and inspect the voice coil gap. Remove all foreign material and make sure it is uniform in shape. Most diaphragms fail because of too much power, distortion, or too low of a cross-over point.
replacing a high frequency driver diaphragm 3.

Test fit the new diaphragm into the housing. See how it lines up and make sure that you have the right part. DO NOT FORCE IT! It should fit perfectly.
replacing a high frequency driver diaphragm 4.

Align the diaphragm into the housing and re-install the screws. DO NOT OVER-TIGHTEN. Too much torque can warp the diaphragm and damage the driver.
replacing a high frequency driver diaphragm 5.

Carefully align the voice coil into the magnet slot. It should fit perfectly and slide in without any friction.
replacing a high frequency driver diaphragm 6.

Line up the holes and tighten the screws firmly but do not over tighten. Sweep test (generate a wide range of frequencies) the driver after connecting it back into the speaker cabinet and connecting it to it's horn or lens. Listen for buzzes or rattles as this is a sign of incorrect installation or other damage.

That's it! Your HF driver should be as good as new! If you need any advice or other info about replacement diaphragms, e-mail us or give us a call at 1.847.963.0733.

 

BMD440.8RD Replacement Diaphragm
BMD440 replacement diaphragm
These are 8-ohm factory original replacement diaphragms for the P Audio BMD-440-8 & BMD-450-8 drivers as well as the Mackie SRM450 Series drivers.

More info...
$54.96

RD2412 Replacement Diaphragm
RD2412 replacement diaphragm
These are 8-ohm factory original replacement diaphragms for the P Audio BMD-440-8 & BMD-450-8 drivers as well as the Mackie SRM450 Series drivers.

More info...
$54.96

PHT.8RD Replacement Diaphragm
PHT.8RD replacement diaphragm
Foster Style phenolic replacement diaphragm, fits Foster/Fostex, PS, Carvin, Yamaha, N30 Foster diaphragm, 1" phenolic for N30, 025H30, 025H27, Ho25N30, FT300H, used in Carvin, PAS, SWR, Peavey, Crate, etc. 8 ohm.

More info...
$15.49



PSD2002.8DIA Replacement Diaphragm
PSD2002.8DIA replacement diaphragm
Replacement Diaphragm for the Eminence PSD-2002 1" high frequency compression driver. It also fits the Yamaha JAY2080 Wave Force series WF-112, Community CPL Series EAW SM155e, Renkus Heinz SSD200-8, SSD-200-8, CD-200-8 SSD2008, CD2008-A and many more.

More info...
$39.99



22XTPlusRD Replacement Diaphragm
22XTRD Plus replacement diaphragm
Replacement diaphragm for Peavey 22XT, 22A, 22T and 22XT Plus Driver.

More info...
$41.99


credit card processing for small business credit cards

Copyright 2011 • LoudspeakersPlus™ • A Division of Jayson Enterprises, Inc. • All Rights Reserved

home_page